Further improvements around acronym lowercases,...

CHANGELOG.md

@@ -9,13 +9,13 @@ and this project adheres to [Semantic Versioning](http://semver.org/).
 
 ### Added
 
-- Added QuickRefresh Trait and implemented it for EPD4in2 in #62 (thanks to @David-OConnor)
+- Added QuickRefresh Trait and implemented it for Epd4in2 in #62 (thanks to @David-OConnor)
 - Added Epd 2in7 (B) support in #60 (thanks to @pjsier)
 
 ### Changed
 
 - Use specific ParseColorError instead of ()
-- EPD4in2: Don't set the resolution (and some more) over and over again (#48)
+- Epd4in2: Don't set the resolution (and some more) over and over again (#48)
 - Removed `#[allow(non_camel_case_types)]` to fix various issues around it
 
 ### Fixed

README.md

@@ -16,7 +16,7 @@ There are multiple examples in the examples folder. Use `cargo run --example exa
 
 ```Rust
 // Setup the epd
-let mut epd = EPD4in2::new( & mut spi, cs, busy, dc, rst, & mut delay) ?;
+let mut epd = Epd4in2::new( & mut spi, cs, busy, dc, rst, & mut delay) ?;
 
 // Setup the graphics
 let mut display = Display4in2::default ();

examples/epd1in54_no_graphics.rs

@@ -1,7 +1,7 @@
 #![deny(warnings)]
 
 use embedded_hal::prelude::*;
-use epd_waveshare::{epd1in54::EPD1in54, prelude::*};
+use epd_waveshare::{epd1in54::Epd1in54, prelude::*};
 use linux_embedded_hal::{
     spidev::{self, SpidevOptions},
     sysfs_gpio::Direction,
@@ -58,14 +58,14 @@ fn main() -> Result<(), std::io::Error> {
 
     // Setup of the needed pins is finished here
     // Now the "real" usage of the eink-waveshare-rs crate begins
-    let mut epd = EPD1in54::new(&mut spi, cs_pin, busy, dc, rst, &mut delay)?;
+    let mut epd = Epd1in54::new(&mut spi, cs_pin, busy, dc, rst, &mut delay)?;
 
     // Clear the full screen
     epd.clear_frame(&mut spi)?;
     epd.display_frame(&mut spi)?;
 
     // Speeddemo
-    epd.set_lut(&mut spi, Some(RefreshLUT::QUICK))?;
+    epd.set_lut(&mut spi, Some(RefreshLut::Quick))?;
     let small_buffer = [Color::Black.get_byte_value(); 32]; //16x16
     let number_of_runs = 1;
     for i in 0..number_of_runs {

examples/epd2in13_v2.rs

@@ -10,7 +10,7 @@ use embedded_graphics::{
 use embedded_hal::prelude::*;
 use epd_waveshare::{
     color::*,
-    epd2in13_v2::{Display2in13, EPD2in13},
+    epd2in13_v2::{Display2in13, Epd2in13},
     graphics::{Display, DisplayRotation},
     prelude::*,
 };
@@ -63,7 +63,7 @@ fn main() -> Result<(), std::io::Error> {
     let mut delay = Delay {};
 
     let mut epd2in13 =
-        EPD2in13::new(&mut spi, cs, busy, dc, rst, &mut delay).expect("eink initalize error");
+        Epd2in13::new(&mut spi, cs, busy, dc, rst, &mut delay).expect("eink initalize error");
 
     //println!("Test all the rotations");
     let mut display = Display2in13::default();
@@ -121,7 +121,7 @@ fn main() -> Result<(), std::io::Error> {
     // Demonstrating how to use the partial refresh feature of the screen.
     // Real animations can be used.
     epd2in13
-        .set_refresh(&mut spi, &mut delay, RefreshLUT::QUICK)
+        .set_refresh(&mut spi, &mut delay, RefreshLut::Quick)
         .unwrap();
     epd2in13.clear_frame(&mut spi).unwrap();
 

examples/epd4in2.rs

@@ -10,7 +10,7 @@ use embedded_graphics::{
 use embedded_hal::prelude::*;
 use epd_waveshare::{
     color::*,
-    epd4in2::{Display4in2, EPD4in2},
+    epd4in2::{Display4in2, Epd4in2},
     graphics::{Display, DisplayRotation},
     prelude::*,
 };
@@ -63,7 +63,7 @@ fn main() -> Result<(), std::io::Error> {
     let mut delay = Delay {};
 
     let mut epd4in2 =
-        EPD4in2::new(&mut spi, cs, busy, dc, rst, &mut delay).expect("eink initalize error");
+        Epd4in2::new(&mut spi, cs, busy, dc, rst, &mut delay).expect("eink initalize error");
 
     //println!("Test all the rotations");
     let mut display = Display4in2::default();
@@ -120,7 +120,7 @@ fn main() -> Result<(), std::io::Error> {
 
     // a moving `Hello World!`
     let limit = 10;
-    epd4in2.set_lut(&mut spi, Some(RefreshLUT::QUICK)).unwrap();
+    epd4in2.set_lut(&mut spi, Some(RefreshLut::Quick)).unwrap();
     epd4in2.clear_frame(&mut spi).unwrap();
     for i in 0..limit {
         //println!("Moving Hello World. Loop {} from {}", (i + 1), limit);

examples/epd4in2_variable_size.rs

@@ -11,7 +11,7 @@ use embedded_graphics::{
 use embedded_hal::prelude::*;
 use epd_waveshare::{
     color::*,
-    epd4in2::{self, EPD4in2},
+    epd4in2::{self, Epd4in2},
     graphics::{Display, DisplayRotation, VarDisplay},
     prelude::*,
 };
@@ -64,7 +64,7 @@ fn main() -> Result<(), std::io::Error> {
     let mut delay = Delay {};
 
     let mut epd4in2 =
-        EPD4in2::new(&mut spi, cs, busy, dc, rst, &mut delay).expect("eink initalize error");
+        Epd4in2::new(&mut spi, cs, busy, dc, rst, &mut delay).expect("eink initalize error");
 
     println!("Test all the rotations");
 

src/epd1in54/mod.rs

@@ -20,7 +20,7 @@
 //!# let mut delay = delay::MockNoop::new();
 //!
 //!// Setup EPD
-//!let mut epd = EPD1in54::new(&mut spi, cs_pin, busy_in, dc, rst, &mut delay)?;
+//!let mut epd = Epd1in54::new(&mut spi, cs_pin, busy_in, dc, rst, &mut delay)?;
 //!
 //!// Use display graphics from embedded-graphics
 //!let mut display = Display1in54::default();
@@ -61,7 +61,7 @@ use crate::type_a::{
 
 use crate::color::Color;
 
-use crate::traits::{RefreshLUT, WaveshareDisplay};
+use crate::traits::{RefreshLut, WaveshareDisplay};
 
 use crate::interface::DisplayInterface;
 
@@ -70,18 +70,18 @@ mod graphics;
 #[cfg(feature = "graphics")]
 pub use crate::epd1in54::graphics::Display1in54;
 
-/// EPD1in54 driver
+/// Epd1in54 driver
 ///
-pub struct EPD1in54<SPI, CS, BUSY, DC, RST> {
+pub struct Epd1in54<SPI, CS, BUSY, DC, RST> {
     /// SPI
     interface: DisplayInterface<SPI, CS, BUSY, DC, RST>,
     /// Color
     background_color: Color,
     /// Refresh LUT
-    refresh: RefreshLUT,
+    refresh: RefreshLut,
 }
 
-impl<SPI, CS, BUSY, DC, RST> EPD1in54<SPI, CS, BUSY, DC, RST>
+impl<SPI, CS, BUSY, DC, RST> Epd1in54<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -140,7 +140,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST, E> WaveshareDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD1in54<SPI, CS, BUSY, DC, RST>
+    for Epd1in54<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8, Error = E>,
     CS: OutputPin,
@@ -167,10 +167,10 @@ where
     ) -> Result<Self, SPI::Error> {
         let interface = DisplayInterface::new(cs, busy, dc, rst);
 
-        let mut epd = EPD1in54 {
+        let mut epd = Epd1in54 {
             interface,
             background_color: DEFAULT_BACKGROUND_COLOR,
-            refresh: RefreshLUT::FULL,
+            refresh: RefreshLut::Full,
         };
 
         epd.init(spi, delay)?;
@@ -232,7 +232,7 @@ where
         self.interface.cmd(spi, Command::MasterActivation)?;
         // MASTER Activation should not be interupted to avoid currption of panel images
         // therefore a terminate command is send
-        self.interface.cmd(spi, Command::NOP)?;
+        self.interface.cmd(spi, Command::Nop)?;
         Ok(())
     }
 
@@ -266,14 +266,14 @@ where
     fn set_lut(
         &mut self,
         spi: &mut SPI,
-        refresh_rate: Option<RefreshLUT>,
+        refresh_rate: Option<RefreshLut>,
     ) -> Result<(), SPI::Error> {
         if let Some(refresh_lut) = refresh_rate {
             self.refresh = refresh_lut;
         }
         match self.refresh {
-            RefreshLUT::FULL => self.set_lut_helper(spi, &LUT_FULL_UPDATE),
-            RefreshLUT::QUICK => self.set_lut_helper(spi, &LUT_PARTIAL_UPDATE),
+            RefreshLut::Full => self.set_lut_helper(spi, &LUT_FULL_UPDATE),
+            RefreshLut::Quick => self.set_lut_helper(spi, &LUT_PARTIAL_UPDATE),
         }
     }
 
@@ -282,7 +282,7 @@ where
     }
 }
 
-impl<SPI, CS, BUSY, DC, RST> EPD1in54<SPI, CS, BUSY, DC, RST>
+impl<SPI, CS, BUSY, DC, RST> Epd1in54<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,

src/epd1in54b/command.rs

@@ -24,7 +24,7 @@ pub(crate) enum Command {
     LutRed1 = 0x27,
 
     PllControl = 0x30,
-    TemperatureSensorCommand = 0x40,
+    TemperatureSensor = 0x40,
     TemperatureSensorSelection = 0x41,
     VcomAndDataIntervalSetting = 0x50,
     ResolutionSetting = 0x61,

src/epd1in54b/mod.rs

@@ -7,7 +7,7 @@ use embedded_hal::{
 
 use crate::interface::DisplayInterface;
 use crate::traits::{
-    InternalWiAdditions, RefreshLUT, WaveshareDisplay, WaveshareThreeColorDisplay,
+    InternalWiAdditions, RefreshLut, WaveshareDisplay, WaveshareThreeColorDisplay,
 };
 
 //The Lookup Tables for the Display
@@ -32,14 +32,14 @@ mod graphics;
 #[cfg(feature = "graphics")]
 pub use self::graphics::Display1in54b;
 
-/// EPD1in54b driver
-pub struct EPD1in54b<SPI, CS, BUSY, DC, RST> {
+/// Epd1in54b driver
+pub struct Epd1in54b<SPI, CS, BUSY, DC, RST> {
     interface: DisplayInterface<SPI, CS, BUSY, DC, RST>,
     color: Color,
 }
 
 impl<SPI, CS, BUSY, DC, RST> InternalWiAdditions<SPI, CS, BUSY, DC, RST>
-    for EPD1in54b<SPI, CS, BUSY, DC, RST>
+    for Epd1in54b<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -89,7 +89,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> WaveshareThreeColorDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD1in54b<SPI, CS, BUSY, DC, RST>
+    for Epd1in54b<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -132,7 +132,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> WaveshareDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD1in54b<SPI, CS, BUSY, DC, RST>
+    for Epd1in54b<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -152,7 +152,7 @@ where
         let interface = DisplayInterface::new(cs, busy, dc, rst);
         let color = DEFAULT_BACKGROUND_COLOR;
 
-        let mut epd = EPD1in54b { interface, color };
+        let mut epd = Epd1in54b { interface, color };
 
         epd.init(spi, delay)?;
 
@@ -165,7 +165,7 @@ where
             .cmd_with_data(spi, Command::VcomAndDataIntervalSetting, &[0x17])?; //border floating
 
         self.interface
-            .cmd_with_data(spi, Command::VcmDcSetting, &[0x00])?; // VCOM to 0V
+            .cmd_with_data(spi, Command::VcmDcSetting, &[0x00])?; // Vcom to 0V
 
         self.interface
             .cmd_with_data(spi, Command::PowerSetting, &[0x02, 0x00, 0x00, 0x00])?; //VG&VS to 0V fast
@@ -276,7 +276,7 @@ where
     fn set_lut(
         &mut self,
         spi: &mut SPI,
-        _refresh_rate: Option<RefreshLUT>,
+        _refresh_rate: Option<RefreshLut>,
     ) -> Result<(), SPI::Error> {
         self.interface
             .cmd_with_data(spi, Command::LutForVcom, LUT_VCOM0)?;
@@ -301,7 +301,7 @@ where
     }
 }
 
-impl<SPI, CS, BUSY, DC, RST> EPD1in54b<SPI, CS, BUSY, DC, RST>
+impl<SPI, CS, BUSY, DC, RST> Epd1in54b<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,

src/epd1in54c/command.rs

@@ -22,7 +22,7 @@ pub(crate) enum Command {
     LutBlackToBlack = 0x24,
 
     PllControl = 0x30,
-    TemperatureSensorCommand = 0x40,
+    TemperatureSensor = 0x40,
     TemperatureSensorSelection = 0x41,
     VcomAndDataIntervalSetting = 0x50,
     ResolutionSetting = 0x61,

src/epd1in54c/mod.rs

@@ -7,7 +7,7 @@ use embedded_hal::{
 
 use crate::interface::DisplayInterface;
 use crate::traits::{
-    InternalWiAdditions, RefreshLUT, WaveshareDisplay, WaveshareThreeColorDisplay,
+    InternalWiAdditions, RefreshLut, WaveshareDisplay, WaveshareThreeColorDisplay,
 };
 
 /// Width of epd1in54 in pixels
@@ -30,14 +30,14 @@ mod graphics;
 #[cfg(feature = "graphics")]
 pub use self::graphics::Display1in54c;
 
-/// EPD1in54c driver
-pub struct EPD1in54c<SPI, CS, BUSY, DC, RST> {
+/// Epd1in54c driver
+pub struct Epd1in54c<SPI, CS, BUSY, DC, RST> {
     interface: DisplayInterface<SPI, CS, BUSY, DC, RST>,
     color: Color,
 }
 
 impl<SPI, CS, BUSY, DC, RST> InternalWiAdditions<SPI, CS, BUSY, DC, RST>
-    for EPD1in54c<SPI, CS, BUSY, DC, RST>
+    for Epd1in54c<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -77,7 +77,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> WaveshareThreeColorDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD1in54c<SPI, CS, BUSY, DC, RST>
+    for Epd1in54c<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -115,7 +115,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> WaveshareDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD1in54c<SPI, CS, BUSY, DC, RST>
+    for Epd1in54c<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -135,7 +135,7 @@ where
         let interface = DisplayInterface::new(cs, busy, dc, rst);
         let color = DEFAULT_BACKGROUND_COLOR;
 
-        let mut epd = EPD1in54c { interface, color };
+        let mut epd = Epd1in54c { interface, color };
 
         epd.init(spi, delay)?;
 
@@ -233,7 +233,7 @@ where
     fn set_lut(
         &mut self,
         _spi: &mut SPI,
-        _refresh_rate: Option<RefreshLUT>,
+        _refresh_rate: Option<RefreshLut>,
     ) -> Result<(), SPI::Error> {
         Ok(())
     }
@@ -243,7 +243,7 @@ where
     }
 }
 
-impl<SPI, CS, BUSY, DC, RST> EPD1in54c<SPI, CS, BUSY, DC, RST>
+impl<SPI, CS, BUSY, DC, RST> Epd1in54c<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,

src/epd2in13_v2/command.rs

@@ -5,7 +5,7 @@ use crate::traits;
 extern crate bit_field;
 use bit_field::BitField;
 
-/// EPD2in13 v2
+/// Epd2in13 v2
 ///
 /// For more infos about the addresses and what they are doing look into the pdfs
 #[allow(dead_code)]
@@ -54,7 +54,7 @@ pub(crate) enum Command {
     SetAnalogBlockControl = 0x74,
     SetDigitalBlockControl = 0x7E,
 
-    NOP = 0x7F,
+    Nop = 0x7F,
 }
 
 pub(crate) struct DriverOutput {
@@ -151,34 +151,34 @@ pub(crate) enum DataEntryModeDir {
 
 #[allow(dead_code)]
 #[derive(Copy, Clone)]
-pub(crate) enum BorderWaveFormVBD {
-    GS = 0x0,
+pub(crate) enum BorderWaveFormVbd {
+    Gs = 0x0,
     FixLevel = 0x1,
-    VCOM = 0x2,
+    Vcom = 0x2,
 }
 
 #[allow(dead_code)]
 #[derive(Copy, Clone)]
 pub(crate) enum BorderWaveFormFixLevel {
-    VSS = 0x0,
-    VSH1 = 0x1,
-    VSL = 0x2,
-    VSH2 = 0x3,
+    Vss = 0x0,
+    Vsh1 = 0x1,
+    Vsl = 0x2,
+    Vsh2 = 0x3,
 }
 
 #[allow(dead_code)]
 #[derive(Copy, Clone)]
-pub(crate) enum BorderWaveFormGS {
-    LUT0 = 0x0,
-    LUT1 = 0x1,
-    LUT2 = 0x2,
-    LUT3 = 0x3,
+pub(crate) enum BorderWaveFormGs {
+    Lut0 = 0x0,
+    Lut1 = 0x1,
+    Lut2 = 0x2,
+    Lut3 = 0x3,
 }
 
 pub(crate) struct BorderWaveForm {
-    pub vbd: BorderWaveFormVBD,
+    pub vbd: BorderWaveFormVbd,
     pub fix_level: BorderWaveFormFixLevel,
-    pub gs_trans: BorderWaveFormGS,
+    pub gs_trans: BorderWaveFormGs,
 }
 
 impl BorderWaveForm {
@@ -204,10 +204,10 @@ pub enum DeepSleepMode {
 
 pub(crate) struct GateDrivingVoltage(pub u8);
 pub(crate) struct SourceDrivingVoltage(pub u8);
-pub(crate) struct VCOM(pub u8);
+pub(crate) struct Vcom(pub u8);
 
 pub(crate) trait I32Ext {
-    fn vcom(self) -> VCOM;
+    fn vcom(self) -> Vcom;
     fn gate_driving_decivolt(self) -> GateDrivingVoltage;
     fn source_driving_decivolt(self) -> SourceDrivingVoltage;
 }
@@ -215,7 +215,7 @@ pub(crate) trait I32Ext {
 impl I32Ext for i32 {
     // This is really not very nice. Until I find something better, this will be
     // a placeholder.
-    fn vcom(self) -> VCOM {
+    fn vcom(self) -> Vcom {
         assert!((-30..=-2).contains(&self));
         let u = match -self {
             2 => 0x08,
@@ -249,7 +249,7 @@ impl I32Ext for i32 {
             30 => 0x78,
             _ => 0,
         };
-        VCOM(u)
+        Vcom(u)
     }
 
     fn gate_driving_decivolt(self) -> GateDrivingVoltage {

src/epd2in13_v2/mod.rs

@@ -16,13 +16,13 @@ use embedded_hal::{
 use crate::buffer_len;
 use crate::color::Color;
 use crate::interface::DisplayInterface;
-use crate::traits::{InternalWiAdditions, RefreshLUT, WaveshareDisplay};
+use crate::traits::{InternalWiAdditions, RefreshLut, WaveshareDisplay};
 
 pub(crate) mod command;
 use self::command::{
-    BorderWaveForm, BorderWaveFormFixLevel, BorderWaveFormGS, BorderWaveFormVBD, Command,
+    BorderWaveForm, BorderWaveFormFixLevel, BorderWaveFormGs, BorderWaveFormVbd, Command,
     DataEntryModeDir, DataEntryModeIncr, DeepSleepMode, DisplayUpdateControl2, DriverOutput,
-    GateDrivingVoltage, I32Ext, SourceDrivingVoltage, VCOM,
+    GateDrivingVoltage, I32Ext, SourceDrivingVoltage, Vcom,
 };
 
 pub(crate) mod constants;
@@ -43,9 +43,9 @@ pub const HEIGHT: u32 = 250;
 pub const DEFAULT_BACKGROUND_COLOR: Color = Color::White;
 const IS_BUSY_LOW: bool = false;
 
-/// EPD2in13 (V2) driver
+/// Epd2in13 (V2) driver
 ///
-pub struct EPD2in13<SPI, CS, BUSY, DC, RST> {
+pub struct Epd2in13<SPI, CS, BUSY, DC, RST> {
     /// Connection Interface
     interface: DisplayInterface<SPI, CS, BUSY, DC, RST>,
 
@@ -53,11 +53,11 @@ pub struct EPD2in13<SPI, CS, BUSY, DC, RST> {
 
     /// Background Color
     background_color: Color,
-    refresh: RefreshLUT,
+    refresh: RefreshLut,
 }
 
 impl<SPI, CS, BUSY, DC, RST> InternalWiAdditions<SPI, CS, BUSY, DC, RST>
-    for EPD2in13<SPI, CS, BUSY, DC, RST>
+    for Epd2in13<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -73,7 +73,7 @@ where
         // HW reset
         self.interface.reset(delay, 10);
 
-        if self.refresh == RefreshLUT::QUICK {
+        if self.refresh == RefreshLut::Quick {
             self.set_vcom_register(spi, (-9).vcom())?;
             self.wait_until_idle();
 
@@ -94,9 +94,9 @@ where
             self.set_border_waveform(
                 spi,
                 BorderWaveForm {
-                    vbd: BorderWaveFormVBD::GS,
-                    fix_level: BorderWaveFormFixLevel::VSS,
-                    gs_trans: BorderWaveFormGS::LUT1,
+                    vbd: BorderWaveFormVbd::Gs,
+                    fix_level: BorderWaveFormFixLevel::Vss,
+                    gs_trans: BorderWaveFormGs::Lut1,
                 },
             )?;
         } else {
@@ -127,9 +127,9 @@ where
             self.set_border_waveform(
                 spi,
                 BorderWaveForm {
-                    vbd: BorderWaveFormVBD::GS,
-                    fix_level: BorderWaveFormFixLevel::VSS,
-                    gs_trans: BorderWaveFormGS::LUT3,
+                    vbd: BorderWaveFormVbd::Gs,
+                    fix_level: BorderWaveFormFixLevel::Vss,
+                    gs_trans: BorderWaveFormGs::Lut3,
                 },
             )?;
 
@@ -154,7 +154,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> WaveshareDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD2in13<SPI, CS, BUSY, DC, RST>
+    for Epd2in13<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -171,11 +171,11 @@ where
         rst: RST,
         delay: &mut DELAY,
     ) -> Result<Self, SPI::Error> {
-        let mut epd = EPD2in13 {
+        let mut epd = Epd2in13 {
             interface: DisplayInterface::new(cs, busy, dc, rst),
             sleep_mode: DeepSleepMode::Mode1,
             background_color: DEFAULT_BACKGROUND_COLOR,
-            refresh: RefreshLUT::FULL,
+            refresh: RefreshLut::Full,
         };
 
         epd.init(spi, delay)?;
@@ -215,7 +215,7 @@ where
 
         self.cmd_with_data(spi, Command::WriteRam, buffer)?;
 
-        if self.refresh == RefreshLUT::FULL {
+        if self.refresh == RefreshLut::Full {
             // Always keep the base buffer equal to current if not doing partial refresh.
             self.set_ram_area(spi, 0, 0, WIDTH - 1, HEIGHT - 1)?;
             self.set_ram_address_counters(spi, 0, 0)?;
@@ -245,14 +245,14 @@ where
         // RAM content). Using this function will most probably make the actual
         // display incorrect as the controler will compare with something
         // incorrect.
-        assert!(self.refresh == RefreshLUT::FULL);
+        assert!(self.refresh == RefreshLut::Full);
 
         self.set_ram_area(spi, x, y, x + width, y + height)?;
         self.set_ram_address_counters(spi, x, y)?;
 
         self.cmd_with_data(spi, Command::WriteRam, buffer)?;
 
-        if self.refresh == RefreshLUT::FULL {
+        if self.refresh == RefreshLut::Full {
             // Always keep the base buffer equals to current if not doing partial refresh.
             self.set_ram_area(spi, x, y, x + width, y + height)?;
             self.set_ram_address_counters(spi, x, y)?;
@@ -266,7 +266,7 @@ where
     /// Never use directly this function when using partial refresh, or also
     /// keep the base buffer in syncd using `set_partial_base_buffer` function.
     fn display_frame(&mut self, spi: &mut SPI) -> Result<(), SPI::Error> {
-        if self.refresh == RefreshLUT::FULL {
+        if self.refresh == RefreshLut::Full {
             self.set_display_update_control_2(
                 spi,
                 DisplayUpdateControl2::new()
@@ -289,7 +289,7 @@ where
         self.update_frame(spi, buffer)?;
         self.display_frame(spi)?;
 
-        if self.refresh == RefreshLUT::QUICK {
+        if self.refresh == RefreshLut::Quick {
             self.set_partial_base_buffer(spi, buffer)?;
         }
         Ok(())
@@ -309,7 +309,7 @@ where
         )?;
 
         // Always keep the base buffer equals to current if not doing partial refresh.
-        if self.refresh == RefreshLUT::FULL {
+        if self.refresh == RefreshLut::Full {
             self.set_ram_area(spi, 0, 0, WIDTH - 1, HEIGHT - 1)?;
             self.set_ram_address_counters(spi, 0, 0)?;
 
@@ -342,11 +342,11 @@ where
     fn set_lut(
         &mut self,
         spi: &mut SPI,
-        refresh_rate: Option<RefreshLUT>,
+        refresh_rate: Option<RefreshLut>,
     ) -> Result<(), SPI::Error> {
         let buffer = match refresh_rate {
-            Some(RefreshLUT::FULL) | None => &LUT_FULL_UPDATE,
-            Some(RefreshLUT::QUICK) => &LUT_PARTIAL_UPDATE,
+            Some(RefreshLut::Full) | None => &LUT_FULL_UPDATE,
+            Some(RefreshLut::Quick) => &LUT_PARTIAL_UPDATE,
         };
 
         self.cmd_with_data(spi, Command::WriteLutRegister, buffer)
@@ -357,7 +357,7 @@ where
     }
 }
 
-impl<SPI, CS, BUSY, DC, RST> EPD2in13<SPI, CS, BUSY, DC, RST>
+impl<SPI, CS, BUSY, DC, RST> Epd2in13<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -391,7 +391,7 @@ where
         &mut self,
         spi: &mut SPI,
         delay: &mut DELAY,
-        refresh: RefreshLUT,
+        refresh: RefreshLut,
     ) -> Result<(), SPI::Error> {
         if self.refresh != refresh {
             self.refresh = refresh;
@@ -425,7 +425,7 @@ where
         )
     }
 
-    fn set_vcom_register(&mut self, spi: &mut SPI, vcom: VCOM) -> Result<(), SPI::Error> {
+    fn set_vcom_register(&mut self, spi: &mut SPI, vcom: Vcom) -> Result<(), SPI::Error> {
         self.cmd_with_data(spi, Command::WriteVcomRegister, &[vcom.0])
     }
 

src/epd2in7b/command.rs

@@ -71,7 +71,7 @@ pub(crate) enum Command {
     /// This command reads the temperature sensed by the temperature sensor.
     ///
     /// Doesn't work! Waveshare doesn't connect the read pin
-    TemperatureSensorCommand = 0x40,
+    TemperatureSensor = 0x40,
     /// This command selects Internal or External temperature sensor.
     TemperatureSensorCalibration = 0x41,
     /// Write External Temperature Sensor

src/epd2in7b/mod.rs

@@ -9,7 +9,7 @@ use embedded_hal::{
 
 use crate::interface::DisplayInterface;
 use crate::traits::{
-    InternalWiAdditions, RefreshLUT, WaveshareDisplay, WaveshareThreeColorDisplay,
+    InternalWiAdditions, RefreshLut, WaveshareDisplay, WaveshareThreeColorDisplay,
 };
 
 // The Lookup Tables for the Display
@@ -34,8 +34,8 @@ mod graphics;
 #[cfg(feature = "graphics")]
 pub use self::graphics::Display2in7b;
 
-/// EPD2in7b driver
-pub struct EPD2in7b<SPI, CS, BUSY, DC, RST> {
+/// Epd2in7b driver
+pub struct Epd2in7b<SPI, CS, BUSY, DC, RST> {
     /// Connection Interface
     interface: DisplayInterface<SPI, CS, BUSY, DC, RST>,
     /// Background Color
@@ -43,7 +43,7 @@ pub struct EPD2in7b<SPI, CS, BUSY, DC, RST> {
 }
 
 impl<SPI, CS, BUSY, DC, RST> InternalWiAdditions<SPI, CS, BUSY, DC, RST>
-    for EPD2in7b<SPI, CS, BUSY, DC, RST>
+    for Epd2in7b<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -112,7 +112,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> WaveshareDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD2in7b<SPI, CS, BUSY, DC, RST>
+    for Epd2in7b<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -132,7 +132,7 @@ where
         let interface = DisplayInterface::new(cs, busy, dc, rst);
         let color = DEFAULT_BACKGROUND_COLOR;
 
-        let mut epd = EPD2in7b { interface, color };
+        let mut epd = Epd2in7b { interface, color };
 
         epd.init(spi, delay)?;
 
@@ -247,7 +247,7 @@ where
     fn set_lut(
         &mut self,
         spi: &mut SPI,
-        _refresh_rate: Option<RefreshLUT>,
+        _refresh_rate: Option<RefreshLut>,
     ) -> Result<(), SPI::Error> {
         self.wait_until_idle();
         self.cmd_with_data(spi, Command::LutForVcom, &LUT_VCOM_DC)?;
@@ -264,7 +264,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> WaveshareThreeColorDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD2in7b<SPI, CS, BUSY, DC, RST>
+    for Epd2in7b<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -316,7 +316,7 @@ where
     }
 }
 
-impl<SPI, CS, BUSY, DC, RST> EPD2in7b<SPI, CS, BUSY, DC, RST>
+impl<SPI, CS, BUSY, DC, RST> Epd2in7b<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,

src/epd2in9/mod.rs

@@ -21,7 +21,7 @@
 //!# let mut delay = delay::MockNoop::new();
 //!
 //!// Setup EPD
-//!let mut epd = EPD2in9::new(&mut spi, cs_pin, busy_in, dc, rst, &mut delay)?;
+//!let mut epd = Epd2in9::new(&mut spi, cs_pin, busy_in, dc, rst, &mut delay)?;
 //!
 //!// Use display graphics from embedded-graphics
 //!let mut display = Display2in9::default();
@@ -70,18 +70,18 @@ mod graphics;
 #[cfg(feature = "graphics")]
 pub use crate::epd2in9::graphics::Display2in9;
 
-/// EPD2in9 driver
+/// Epd2in9 driver
 ///
-pub struct EPD2in9<SPI, CS, BUSY, DC, RST> {
+pub struct Epd2in9<SPI, CS, BUSY, DC, RST> {
     /// SPI
     interface: DisplayInterface<SPI, CS, BUSY, DC, RST>,
     /// Color
     background_color: Color,
     /// Refresh LUT
-    refresh: RefreshLUT,
+    refresh: RefreshLut,
 }
 
-impl<SPI, CS, BUSY, DC, RST> EPD2in9<SPI, CS, BUSY, DC, RST>
+impl<SPI, CS, BUSY, DC, RST> Epd2in9<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -136,7 +136,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> WaveshareDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD2in9<SPI, CS, BUSY, DC, RST>
+    for Epd2in9<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -163,10 +163,10 @@ where
     ) -> Result<Self, SPI::Error> {
         let interface = DisplayInterface::new(cs, busy, dc, rst);
 
-        let mut epd = EPD2in9 {
+        let mut epd = Epd2in9 {
             interface,
             background_color: DEFAULT_BACKGROUND_COLOR,
-            refresh: RefreshLUT::FULL,
+            refresh: RefreshLut::Full,
         };
 
         epd.init(spi, delay)?;
@@ -231,7 +231,7 @@ where
         self.interface.cmd(spi, Command::MasterActivation)?;
         // MASTER Activation should not be interupted to avoid currption of panel images
         // therefore a terminate command is send
-        self.interface.cmd(spi, Command::NOP)?;
+        self.interface.cmd(spi, Command::Nop)?;
         Ok(())
     }
 
@@ -265,14 +265,14 @@ where
     fn set_lut(
         &mut self,
         spi: &mut SPI,
-        refresh_rate: Option<RefreshLUT>,
+        refresh_rate: Option<RefreshLut>,
     ) -> Result<(), SPI::Error> {
         if let Some(refresh_lut) = refresh_rate {
             self.refresh = refresh_lut;
         }
         match self.refresh {
-            RefreshLUT::FULL => self.set_lut_helper(spi, &LUT_FULL_UPDATE),
-            RefreshLUT::QUICK => self.set_lut_helper(spi, &LUT_PARTIAL_UPDATE),
+            RefreshLut::Full => self.set_lut_helper(spi, &LUT_FULL_UPDATE),
+            RefreshLut::Quick => self.set_lut_helper(spi, &LUT_PARTIAL_UPDATE),
         }
     }
 
@@ -281,7 +281,7 @@ where
     }
 }
 
-impl<SPI, CS, BUSY, DC, RST> EPD2in9<SPI, CS, BUSY, DC, RST>
+impl<SPI, CS, BUSY, DC, RST> Epd2in9<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,

src/epd2in9bc/command.rs

@@ -22,7 +22,7 @@ pub(crate) enum Command {
     LutBlackToBlack = 0x24,
 
     PllControl = 0x30,
-    TemperatureSensorCommand = 0x40,
+    TemperatureSensor = 0x40,
     TemperatureSensorSelection = 0x41,
     VcomAndDataIntervalSetting = 0x50,
     ResolutionSetting = 0x61,

src/epd2in9bc/mod.rs

@@ -20,7 +20,7 @@
 //!# let mut delay = delay::MockNoop::new();
 //!
 //!// Setup EPD
-//!let mut epd = EPD2in9bc::new(&mut spi, cs_pin, busy_in, dc, rst, &mut delay)?;
+//!let mut epd = Epd2in9bc::new(&mut spi, cs_pin, busy_in, dc, rst, &mut delay)?;
 //!
 //!// Use display graphics from embedded-graphics
 //!// This display is for the black/white pixels
@@ -60,7 +60,7 @@ use embedded_hal::{
 
 use crate::interface::DisplayInterface;
 use crate::traits::{
-    InternalWiAdditions, RefreshLUT, WaveshareDisplay, WaveshareThreeColorDisplay,
+    InternalWiAdditions, RefreshLut, WaveshareDisplay, WaveshareThreeColorDisplay,
 };
 
 /// Width of epd2in9bc in pixels
@@ -89,14 +89,14 @@ mod graphics;
 #[cfg(feature = "graphics")]
 pub use self::graphics::Display2in9bc;
 
-/// EPD2in9bc driver
-pub struct EPD2in9bc<SPI, CS, BUSY, DC, RST> {
+/// Epd2in9bc driver
+pub struct Epd2in9bc<SPI, CS, BUSY, DC, RST> {
     interface: DisplayInterface<SPI, CS, BUSY, DC, RST>,
     color: Color,
 }
 
 impl<SPI, CS, BUSY, DC, RST> InternalWiAdditions<SPI, CS, BUSY, DC, RST>
-    for EPD2in9bc<SPI, CS, BUSY, DC, RST>
+    for Epd2in9bc<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -143,7 +143,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> WaveshareThreeColorDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD2in9bc<SPI, CS, BUSY, DC, RST>
+    for Epd2in9bc<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -187,7 +187,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> WaveshareDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD2in9bc<SPI, CS, BUSY, DC, RST>
+    for Epd2in9bc<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -207,7 +207,7 @@ where
         let interface = DisplayInterface::new(cs, busy, dc, rst);
         let color = DEFAULT_BACKGROUND_COLOR;
 
-        let mut epd = EPD2in9bc { interface, color };
+        let mut epd = Epd2in9bc { interface, color };
 
         epd.init(spi, delay)?;
 
@@ -317,7 +317,7 @@ where
     fn set_lut(
         &mut self,
         _spi: &mut SPI,
-        _refresh_rate: Option<RefreshLUT>,
+        _refresh_rate: Option<RefreshLut>,
     ) -> Result<(), SPI::Error> {
         Ok(())
     }
@@ -327,7 +327,7 @@ where
     }
 }
 
-impl<SPI, CS, BUSY, DC, RST> EPD2in9bc<SPI, CS, BUSY, DC, RST>
+impl<SPI, CS, BUSY, DC, RST> Epd2in9bc<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,

src/epd4in2/command.rs

@@ -92,7 +92,7 @@ pub(crate) enum Command {
     /// This command reads the temperature sensed by the temperature sensor.
     ///
     /// Doesn't work! Waveshare doesn't connect the read pin
-    TemperatureSensorCommand = 0x40,
+    TemperatureSensor = 0x40,
     /// Selects the Internal or External temperature sensor and offset
     TemperatureSensorSelection = 0x41,
     /// Write External Temperature Sensor
@@ -114,7 +114,7 @@ pub(crate) enum Command {
     /// The LUT_REV / Chip Revision is read from OTP address = 0x001.
     ///
     /// Doesn't work! Waveshare doesn't connect the read pin
-    REVISION = 0x70,
+    Revision = 0x70,
     /// Read Flags. This command reads the IC status
     /// PTL, I2C_ERR, I2C_BUSY, DATA, PON, POF, BUSY
     ///

src/epd4in2/mod.rs

@@ -25,7 +25,7 @@
 //!# let mut delay = delay::MockNoop::new();
 //!
 //!// Setup EPD
-//!let mut epd = EPD4in2::new(&mut spi, cs_pin, busy_in, dc, rst, &mut delay)?;
+//!let mut epd = Epd4in2::new(&mut spi, cs_pin, busy_in, dc, rst, &mut delay)?;
 //!
 //!// Use display graphics from embedded-graphics
 //!let mut display = Display4in2::default();
@@ -55,7 +55,7 @@ use embedded_hal::{
 };
 
 use crate::interface::DisplayInterface;
-use crate::traits::{InternalWiAdditions, QuickRefresh, RefreshLUT, WaveshareDisplay};
+use crate::traits::{InternalWiAdditions, QuickRefresh, RefreshLut, WaveshareDisplay};
 
 //The Lookup Tables for the Display
 mod constants;
@@ -79,19 +79,19 @@ mod graphics;
 #[cfg(feature = "graphics")]
 pub use self::graphics::Display4in2;
 
-/// EPD4in2 driver
+/// Epd4in2 driver
 ///
-pub struct EPD4in2<SPI, CS, BUSY, DC, RST> {
+pub struct Epd4in2<SPI, CS, BUSY, DC, RST> {
     /// Connection Interface
     interface: DisplayInterface<SPI, CS, BUSY, DC, RST>,
     /// Background Color
     color: Color,
     /// Refresh LUT
-    refresh: RefreshLUT,
+    refresh: RefreshLut,
 }
 
 impl<SPI, CS, BUSY, DC, RST> InternalWiAdditions<SPI, CS, BUSY, DC, RST>
-    for EPD4in2<SPI, CS, BUSY, DC, RST>
+    for Epd4in2<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -149,7 +149,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> WaveshareDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD4in2<SPI, CS, BUSY, DC, RST>
+    for Epd4in2<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -169,10 +169,10 @@ where
         let interface = DisplayInterface::new(cs, busy, dc, rst);
         let color = DEFAULT_BACKGROUND_COLOR;
 
-        let mut epd = EPD4in2 {
+        let mut epd = Epd4in2 {
             interface,
             color,
-            refresh: RefreshLUT::FULL,
+            refresh: RefreshLut::Full,
         };
 
         epd.init(spi, delay)?;
@@ -313,16 +313,16 @@ where
     fn set_lut(
         &mut self,
         spi: &mut SPI,
-        refresh_rate: Option<RefreshLUT>,
+        refresh_rate: Option<RefreshLut>,
     ) -> Result<(), SPI::Error> {
         if let Some(refresh_lut) = refresh_rate {
             self.refresh = refresh_lut;
         }
         match self.refresh {
-            RefreshLUT::FULL => {
+            RefreshLut::Full => {
                 self.set_lut_helper(spi, &LUT_VCOM0, &LUT_WW, &LUT_BW, &LUT_WB, &LUT_BB)
             }
-            RefreshLUT::QUICK => self.set_lut_helper(
+            RefreshLut::Quick => self.set_lut_helper(
                 spi,
                 &LUT_VCOM0_QUICK,
                 &LUT_WW_QUICK,
@@ -338,7 +338,7 @@ where
     }
 }
 
-impl<SPI, CS, BUSY, DC, RST> EPD4in2<SPI, CS, BUSY, DC, RST>
+impl<SPI, CS, BUSY, DC, RST> Epd4in2<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -435,7 +435,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> QuickRefresh<SPI, CS, BUSY, DC, RST>
-    for EPD4in2<SPI, CS, BUSY, DC, RST>
+    for Epd4in2<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,

src/epd5in65f/command.rs

@@ -64,7 +64,7 @@ pub(crate) enum Command {
     DisplayRefresh = 0x12,
 
     /// Image Process Command
-    ImageProcessCommand = 0x13,
+    ImageProcess = 0x13,
 
     /// This command builds the VCOM Look-Up Table (LUTC).
     LutForVcom = 0x20,
@@ -91,7 +91,7 @@ pub(crate) enum Command {
     PllControl = 0x30,
 
     /// This command reads the temperature sensed by the temperature sensor.
-    TemperatureSensorCommand = 0x40,
+    TemperatureSensor = 0x40,
     /// This command selects the Internal or External temperature sensor.
     TemperatureCalibration = 0x41,
     /// This command could write data to the external temperature sensor.
@@ -115,7 +115,7 @@ pub(crate) enum Command {
     //SpiFlashControl = 0x65,
 
     /// The LUT_REV / Chip Revision is read from OTP address = 25001 and 25000.
-    //REVISION = 0x70,
+    //Revision = 0x70,
     /// This command reads the IC status.
     GetStatus = 0x71,
 

src/epd5in65f/mod.rs

@@ -13,7 +13,7 @@ use embedded_hal::{
 
 use crate::color::OctColor;
 use crate::interface::DisplayInterface;
-use crate::traits::{InternalWiAdditions, RefreshLUT, WaveshareDisplay};
+use crate::traits::{InternalWiAdditions, RefreshLut, WaveshareDisplay};
 
 pub(crate) mod command;
 use self::command::Command;
@@ -31,9 +31,9 @@ pub const HEIGHT: u32 = 448;
 pub const DEFAULT_BACKGROUND_COLOR: OctColor = OctColor::White;
 const IS_BUSY_LOW: bool = true;
 
-/// EPD5in65f driver
+/// Epd5in65f driver
 ///
-pub struct EPD5in65f<SPI, CS, BUSY, DC, RST> {
+pub struct Epd5in65f<SPI, CS, BUSY, DC, RST> {
     /// Connection Interface
     interface: DisplayInterface<SPI, CS, BUSY, DC, RST>,
     /// Background Color
@@ -41,7 +41,7 @@ pub struct EPD5in65f<SPI, CS, BUSY, DC, RST> {
 }
 
 impl<SPI, CS, BUSY, DC, RST> InternalWiAdditions<SPI, CS, BUSY, DC, RST>
-    for EPD5in65f<SPI, CS, BUSY, DC, RST>
+    for Epd5in65f<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -62,7 +62,7 @@ where
         self.cmd_with_data(spi, Command::PowerOffSequenceSetting, &[0x00])?;
         self.cmd_with_data(spi, Command::BoosterSoftStart, &[0xC7, 0xC7, 0x1D])?;
         self.cmd_with_data(spi, Command::PllControl, &[0x3C])?;
-        self.cmd_with_data(spi, Command::TemperatureSensorCommand, &[0x00])?;
+        self.cmd_with_data(spi, Command::TemperatureSensor, &[0x00])?;
         self.cmd_with_data(spi, Command::VcomAndDataIntervalSetting, &[0x37])?;
         self.cmd_with_data(spi, Command::TconSetting, &[0x22])?;
         self.send_resolution(spi)?;
@@ -77,7 +77,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> WaveshareDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD5in65f<SPI, CS, BUSY, DC, RST>
+    for Epd5in65f<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -97,7 +97,7 @@ where
         let interface = DisplayInterface::new(cs, busy, dc, rst);
         let color = DEFAULT_BACKGROUND_COLOR;
 
-        let mut epd = EPD5in65f { interface, color };
+        let mut epd = Epd5in65f { interface, color };
 
         epd.init(spi, delay)?;
 
@@ -182,7 +182,7 @@ where
     fn set_lut(
         &mut self,
         _spi: &mut SPI,
-        _refresh_rate: Option<RefreshLUT>,
+        _refresh_rate: Option<RefreshLut>,
     ) -> Result<(), SPI::Error> {
         unimplemented!();
     }
@@ -192,7 +192,7 @@ where
     }
 }
 
-impl<SPI, CS, BUSY, DC, RST> EPD5in65f<SPI, CS, BUSY, DC, RST>
+impl<SPI, CS, BUSY, DC, RST> Epd5in65f<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,

src/epd7in5/command.rs

@@ -2,7 +2,7 @@
 
 use crate::traits;
 
-/// EPD7in5 commands
+/// Epd7in5 commands
 ///
 /// Should rarely (never?) be needed directly.
 ///
@@ -93,7 +93,7 @@ pub(crate) enum Command {
     PllControl = 0x30,
 
     /// This command reads the temperature sensed by the temperature sensor.
-    TemperatureSensorCommand = 0x40,
+    TemperatureSensor = 0x40,
     /// This command selects the Internal or External temperature sensor.
     TemperatureCalibration = 0x41,
     /// This command could write data to the external temperature sensor.
@@ -117,7 +117,7 @@ pub(crate) enum Command {
     SpiFlashControl = 0x65,
 
     /// The LUT_REV / Chip Revision is read from OTP address = 25001 and 25000.
-    REVISION = 0x70,
+    Revision = 0x70,
     /// This command reads the IC status.
     GetStatus = 0x71,
 
@@ -128,7 +128,7 @@ pub(crate) enum Command {
     /// This command sets `VCOM_DC` value.
     VcmDcSetting = 0x82,
 
-    /// This is in all the Waveshare controllers for EPD7in5, but it's not documented
+    /// This is in all the Waveshare controllers for Epd7in5, but it's not documented
     /// anywhere in the datasheet `¯\_(ツ)_/¯`
     FlashMode = 0xE5,
 }

src/epd7in5/mod.rs

@@ -13,7 +13,7 @@ use embedded_hal::{
 
 use crate::color::Color;
 use crate::interface::DisplayInterface;
-use crate::traits::{InternalWiAdditions, RefreshLUT, WaveshareDisplay};
+use crate::traits::{InternalWiAdditions, RefreshLut, WaveshareDisplay};
 
 pub(crate) mod command;
 use self::command::Command;
@@ -31,9 +31,9 @@ pub const HEIGHT: u32 = 384;
 pub const DEFAULT_BACKGROUND_COLOR: Color = Color::White;
 const IS_BUSY_LOW: bool = true;
 
-/// EPD7in5 driver
+/// Epd7in5 driver
 ///
-pub struct EPD7in5<SPI, CS, BUSY, DC, RST> {
+pub struct Epd7in5<SPI, CS, BUSY, DC, RST> {
     /// Connection Interface
     interface: DisplayInterface<SPI, CS, BUSY, DC, RST>,
     /// Background Color
@@ -41,7 +41,7 @@ pub struct EPD7in5<SPI, CS, BUSY, DC, RST> {
 }
 
 impl<SPI, CS, BUSY, DC, RST> InternalWiAdditions<SPI, CS, BUSY, DC, RST>
-    for EPD7in5<SPI, CS, BUSY, DC, RST>
+    for Epd7in5<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -91,7 +91,7 @@ where
         // Set VCOM_DC to -1.5V
         self.cmd_with_data(spi, Command::VcmDcSetting, &[0x1E])?;
 
-        // This is in all the Waveshare controllers for EPD7in5
+        // This is in all the Waveshare controllers for Epd7in5
         self.cmd_with_data(spi, Command::FlashMode, &[0x03])?;
 
         self.wait_until_idle();
@@ -100,7 +100,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> WaveshareDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD7in5<SPI, CS, BUSY, DC, RST>
+    for Epd7in5<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -120,7 +120,7 @@ where
         let interface = DisplayInterface::new(cs, busy, dc, rst);
         let color = DEFAULT_BACKGROUND_COLOR;
 
-        let mut epd = EPD7in5 { interface, color };
+        let mut epd = Epd7in5 { interface, color };
 
         epd.init(spi, delay)?;
 
@@ -214,7 +214,7 @@ where
     fn set_lut(
         &mut self,
         _spi: &mut SPI,
-        _refresh_rate: Option<RefreshLUT>,
+        _refresh_rate: Option<RefreshLut>,
     ) -> Result<(), SPI::Error> {
         unimplemented!();
     }
@@ -224,7 +224,7 @@ where
     }
 }
 
-impl<SPI, CS, BUSY, DC, RST> EPD7in5<SPI, CS, BUSY, DC, RST>
+impl<SPI, CS, BUSY, DC, RST> Epd7in5<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,

src/epd7in5_v2/command.rs

@@ -2,7 +2,7 @@
 
 use crate::traits;
 
-/// EPD7in5 commands
+/// Epd7in5 commands
 ///
 /// Should rarely (never?) be needed directly.
 ///
@@ -94,7 +94,7 @@ pub(crate) enum Command {
     PllControl = 0x30,
 
     /// This command reads the temperature sensed by the temperature sensor.
-    TemperatureSensorCommand = 0x40,
+    TemperatureSensor = 0x40,
     /// This command selects the Internal or External temperature sensor.
     TemperatureCalibration = 0x41,
     /// This command could write data to the external temperature sensor.
@@ -118,7 +118,7 @@ pub(crate) enum Command {
     SpiFlashControl = 0x65,
 
     /// The LUT_REV / Chip Revision is read from OTP address = 25001 and 25000.
-    REVISION = 0x70,
+    Revision = 0x70,
     /// This command reads the IC status.
     GetStatus = 0x71,
 
@@ -128,7 +128,7 @@ pub(crate) enum Command {
     ReadVcomValue = 0x81,
     /// This command sets `VCOM_DC` value.
     VcmDcSetting = 0x82,
-    // /// This is in all the Waveshare controllers for EPD7in5, but it's not documented
+    // /// This is in all the Waveshare controllers for Epd7in5, but it's not documented
     // /// anywhere in the datasheet `¯\_(ツ)_/¯`
     // FlashMode = 0xE5,
 }

src/epd7in5_v2/mod.rs

@@ -17,7 +17,7 @@ use embedded_hal::{
 
 use crate::color::Color;
 use crate::interface::DisplayInterface;
-use crate::traits::{InternalWiAdditions, RefreshLUT, WaveshareDisplay};
+use crate::traits::{InternalWiAdditions, RefreshLut, WaveshareDisplay};
 
 pub(crate) mod command;
 use self::command::Command;
@@ -35,9 +35,9 @@ pub const HEIGHT: u32 = 480;
 pub const DEFAULT_BACKGROUND_COLOR: Color = Color::White;
 const IS_BUSY_LOW: bool = true;
 
-/// EPD7in5 (V2) driver
+/// Epd7in5 (V2) driver
 ///
-pub struct EPD7in5<SPI, CS, BUSY, DC, RST> {
+pub struct Epd7in5<SPI, CS, BUSY, DC, RST> {
     /// Connection Interface
     interface: DisplayInterface<SPI, CS, BUSY, DC, RST>,
     /// Background Color
@@ -45,7 +45,7 @@ pub struct EPD7in5<SPI, CS, BUSY, DC, RST> {
 }
 
 impl<SPI, CS, BUSY, DC, RST> InternalWiAdditions<SPI, CS, BUSY, DC, RST>
-    for EPD7in5<SPI, CS, BUSY, DC, RST>
+    for Epd7in5<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -82,7 +82,7 @@ where
 }
 
 impl<SPI, CS, BUSY, DC, RST> WaveshareDisplay<SPI, CS, BUSY, DC, RST>
-    for EPD7in5<SPI, CS, BUSY, DC, RST>
+    for Epd7in5<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,
@@ -102,7 +102,7 @@ where
         let interface = DisplayInterface::new(cs, busy, dc, rst);
         let color = DEFAULT_BACKGROUND_COLOR;
 
-        let mut epd = EPD7in5 { interface, color };
+        let mut epd = Epd7in5 { interface, color };
 
         epd.init(spi, delay)?;
 
@@ -188,7 +188,7 @@ where
     fn set_lut(
         &mut self,
         _spi: &mut SPI,
-        _refresh_rate: Option<RefreshLUT>,
+        _refresh_rate: Option<RefreshLut>,
     ) -> Result<(), SPI::Error> {
         unimplemented!();
     }
@@ -198,7 +198,7 @@ where
     }
 }
 
-impl<SPI, CS, BUSY, DC, RST> EPD7in5<SPI, CS, BUSY, DC, RST>
+impl<SPI, CS, BUSY, DC, RST> Epd7in5<SPI, CS, BUSY, DC, RST>
 where
     SPI: Write<u8>,
     CS: OutputPin,

src/interface.rs

@@ -51,7 +51,7 @@ where
 
     /// Basic function for sending an array of u8-values of data over spi
     ///
-    /// Enables direct interaction with the device with the help of [command()](EPD4in2::command())
+    /// Enables direct interaction with the device with the help of [command()](Epd4in2::command())
     pub(crate) fn data(&mut self, spi: &mut SPI, data: &[u8]) -> Result<(), SPI::Error> {
         // high for data
         let _ = self.dc.set_high();
@@ -157,7 +157,7 @@ where
 
     /// Resets the device.
     ///
-    /// Often used to awake the module from deep sleep. See [EPD4in2::sleep()](EPD4in2::sleep())
+    /// Often used to awake the module from deep sleep. See [Epd4in2::sleep()](Epd4in2::sleep())
     ///
     /// The timing of keeping the reset pin low seems to be important and different per device.
     /// Most displays seem to require keeping it low for 10ms, but the 7in5_v2 only seems to reset

src/lib.rs

@@ -28,7 +28,7 @@
 //!# let mut delay = delay::MockNoop::new();
 //!
 //!// Setup EPD
-//!let mut epd = EPD1in54::new(&mut spi, cs_pin, busy_in, dc, rst, &mut delay)?;
+//!let mut epd = Epd1in54::new(&mut spi, cs_pin, busy_in, dc, rst, &mut delay)?;
 //!
 //!// Use display graphics from embedded-graphics
 //!let mut display = Display1in54::default();
@@ -90,7 +90,7 @@ pub(crate) mod type_a;
 pub mod prelude {
     pub use crate::color::{Color, OctColor, TriColor};
     pub use crate::traits::{
-        QuickRefresh, RefreshLUT, WaveshareDisplay, WaveshareThreeColorDisplay,
+        QuickRefresh, RefreshLut, WaveshareDisplay, WaveshareThreeColorDisplay,
     };
 
     pub use crate::SPI_MODE;

src/traits.rs

@@ -12,17 +12,17 @@ pub(crate) trait Command {
 
 /// Seperates the different LUT for the Display Refresh process
 #[derive(Debug, Clone, PartialEq, Eq, Copy)]
-pub enum RefreshLUT {
+pub enum RefreshLut {
     /// The "normal" full Lookuptable for the Refresh-Sequence
-    FULL,
+    Full,
     /// The quick LUT where not the full refresh sequence is followed.
     /// This might lead to some
-    QUICK,
+    Quick,
 }
 
-impl Default for RefreshLUT {
+impl Default for RefreshLut {
     fn default() -> Self {
-        RefreshLUT::FULL
+        RefreshLut::Full
     }
 }
 
@@ -108,7 +108,7 @@ where
 ///# let mut delay = delay::MockNoop::new();
 ///
 ///// Setup EPD
-///let mut epd = EPD4in2::new(&mut spi, cs_pin, busy_in, dc, rst, &mut delay)?;
+///let mut epd = Epd4in2::new(&mut spi, cs_pin, busy_in, dc, rst, &mut delay)?;
 ///
 ///// Use display graphics from embedded-graphics
 ///let mut display = Display4in2::default();
@@ -219,7 +219,7 @@ where
     fn set_lut(
         &mut self,
         spi: &mut SPI,
-        refresh_rate: Option<RefreshLUT>,
+        refresh_rate: Option<RefreshLut>,
     ) -> Result<(), SPI::Error>;
 
     /// Checks if the display is busy transmitting data
@@ -258,7 +258,7 @@ where
 ///# let mut delay = delay::MockNoop::new();
 ///#
 ///# // Setup EPD
-///# let mut epd = EPD4in2::new(&mut spi, cs_pin, busy_in, dc, rst, &mut delay)?;
+///# let mut epd = Epd4in2::new(&mut spi, cs_pin, busy_in, dc, rst, &mut delay)?;
 ///let (x, y, frame_width, frame_height) = (20, 40, 80,80);
 ///
 ///let mut buffer = [DEFAULT_BACKGROUND_COLOR.get_byte_value(); 80 / 8 * 80];

src/type_a/command.rs

@@ -2,7 +2,7 @@
 
 use crate::traits;
 
-/// EPD1in54 and EPD2IN9 commands
+/// Epd1in54 and EPD2IN9 commands
 ///
 /// Should rarely (never?) be needed directly.
 ///
@@ -67,7 +67,7 @@ pub(crate) enum Command {
 
     SetRamYAddressCounter = 0x4F,
 
-    NOP = 0xFF,
+    Nop = 0xFF,
 }
 
 impl traits::Command for Command {
@@ -88,6 +88,6 @@ mod tests {
 
         assert_eq!(Command::SetRamXAddressCounter.address(), 0x4E);
 
-        assert_eq!(Command::NOP.address(), 0xFF);
+        assert_eq!(Command::Nop.address(), 0xFF);
     }
 }