mirror of
https://github.com/Anshorei/epd-waveshare.git
synced 2026-10-04 06:16:42 +00:00
Removed #[allow(non_camel_case_types)] to fix issues
This commit is contained in:
Caemor
+40
-41
@@ -5,117 +5,116 @@ use crate::traits;
|
||||
///
|
||||
/// More information can be found in the [specification](https://www.waveshare.com/w/upload/d/d8/2.7inch-e-paper-b-specification.pdf)
|
||||
#[allow(dead_code)]
|
||||
#[allow(non_camel_case_types)]
|
||||
#[derive(Copy, Clone)]
|
||||
pub(crate) enum Command {
|
||||
/// Set Resolution, LUT selection, BWR pixels, gate scan direction, source shift direction, booster switch, soft reset
|
||||
PANEL_SETTING = 0x00,
|
||||
PanelSetting = 0x00,
|
||||
/// Selecting internal and external power
|
||||
POWER_SETTING = 0x01,
|
||||
POWER_OFF = 0x02,
|
||||
PowerSetting = 0x01,
|
||||
PowerOff = 0x02,
|
||||
/// Setting Power OFF sequence
|
||||
POWER_OFF_SEQUENCE_SETTING = 0x03,
|
||||
POWER_ON = 0x04,
|
||||
PowerOffSequenceSetting = 0x03,
|
||||
PowerOn = 0x04,
|
||||
/// This command enables the internal bandgap, which will be cleared by the next POF.
|
||||
POWER_ON_MEASURE = 0x05,
|
||||
PowerOnMeasure = 0x05,
|
||||
/// Starting data transmission
|
||||
///
|
||||
/// ```ignore
|
||||
/// self.send_data(&[0x07, 0x07, 0x17])?;
|
||||
/// ```
|
||||
BOOSTER_SOFT_START = 0x06,
|
||||
BoosterSoftStart = 0x06,
|
||||
/// After this command is transmitted, the chip would enter the deep-sleep mode to save power.
|
||||
///
|
||||
/// The deep sleep mode would return to standby by hardware reset.
|
||||
///
|
||||
/// The only one parameter is a check code, the command would be excuted if check code = 0xA5.
|
||||
DEEP_SLEEP = 0x07,
|
||||
DeepSleep = 0x07,
|
||||
/// This command starts transmitting data and write them into SRAM. To complete data transmission, command DSP (Data
|
||||
/// transmission Stop) must be issued. Then the chip will start to send data/VCOM for panel.
|
||||
///
|
||||
/// - In B/W mode, this command writes “OLD” data to SRAM.
|
||||
/// - In B/W/Red mode, this command writes “B/W” data to SRAM.
|
||||
DATA_START_TRANSMISSION_1 = 0x10,
|
||||
DataStartTransmission1 = 0x10,
|
||||
/// Stopping data transmission
|
||||
DATA_STOP = 0x11,
|
||||
DataStop = 0x11,
|
||||
/// After this command is issued, driver will refresh display (data/VCOM) according to SRAM data and LUT.
|
||||
DISPLAY_REFRESH = 0x12,
|
||||
DisplayRefresh = 0x12,
|
||||
/// This command starts transmitting data and write them into SRAM. To complete data transmission, command DSP (Data
|
||||
/// transmission Stop) must be issued. Then the chip will start to send data/VCOM for panel.
|
||||
/// - In B/W mode, this command writes “NEW” data to SRAM.
|
||||
/// - In B/W/Red mode, this command writes “RED” data to SRAM.
|
||||
DATA_START_TRANSMISSION_2 = 0x13,
|
||||
DataStartTransmission2 = 0x13,
|
||||
/// The command define as follows: The register is indicates that user start to transmit data, then write to SRAM. While data transmission
|
||||
/// complete, user must send command DSP (Data transmission Stop). Then chip will start to send data/VCOM for panel.
|
||||
///
|
||||
/// - In B/W mode, this command writes “OLD” data to SRAM.
|
||||
/// - In B/W/Red mode, this command writes “B/W” data to SRAM.
|
||||
PARTIAL_DATA_START_TRANSMISSION_1 = 0x14,
|
||||
PartialDataStartTransmission1 = 0x14,
|
||||
/// The command define as follows: The register is indicates that user start to transmit data, then write to SRAM. While data transmission
|
||||
/// complete, user must send command DSP (Data transmission Stop). Then chip will start to send data/VCOM for panel.
|
||||
///
|
||||
/// - In B/W mode, this command writes “NEW” data to SRAM.
|
||||
/// - In B/W/Red mode, this command writes “RED” data to SRAM.
|
||||
PARTIAL_DATA_START_TRANSMISSION_2 = 0x15,
|
||||
PartialDataStartTransmission2 = 0x15,
|
||||
/// While user sent this command, driver will refresh display (data/VCOM) base on SRAM data and LUT.
|
||||
///
|
||||
/// Only the area (X,Y, W, L) would update, the others pixel output would follow VCOM LUT
|
||||
PARTIAL_DISPLAY_REFRESH = 0x16,
|
||||
PartialDisplayRefresh = 0x16,
|
||||
/// This command builds the Look-up table for VCOM
|
||||
LUT_FOR_VCOM = 0x20,
|
||||
LUT_WHITE_TO_WHITE = 0x21,
|
||||
LUT_BLACK_TO_WHITE = 0x22,
|
||||
LUT_WHITE_TO_BLACK = 0x23,
|
||||
LUT_BLACK_TO_BLACK = 0x24,
|
||||
LutForVcom = 0x20,
|
||||
LutWhiteToWhite = 0x21,
|
||||
LutBlackToWhite = 0x22,
|
||||
LutWhiteToBlack = 0x23,
|
||||
LutBlackToBlack = 0x24,
|
||||
/// The command controls the PLL clock frequency.
|
||||
PLL_CONTROL = 0x30,
|
||||
PllControl = 0x30,
|
||||
/// This command reads the temperature sensed by the temperature sensor.
|
||||
///
|
||||
/// Doesn't work! Waveshare doesn't connect the read pin
|
||||
TEMPERATURE_SENSOR_COMMAND = 0x40,
|
||||
TemperatureSensorCommand = 0x40,
|
||||
/// This command selects Internal or External temperature sensor.
|
||||
TEMPERATURE_SENSOR_CALIBRATION = 0x41,
|
||||
TemperatureSensorCalibration = 0x41,
|
||||
/// Write External Temperature Sensor
|
||||
TEMPERATURE_SENSOR_WRITE = 0x42,
|
||||
TemperatureSensorWrite = 0x42,
|
||||
/// Read External Temperature Sensor
|
||||
///
|
||||
/// Doesn't work! Waveshare doesn't connect the read pin
|
||||
TEMPERATURE_SENSOR_READ = 0x43,
|
||||
TemperatureSensorRead = 0x43,
|
||||
/// This command indicates the interval of Vcom and data output. When setting the vertical back porch, the total blanking will be kept (20 Hsync)
|
||||
VCOM_AND_DATA_INTERVAL_SETTING = 0x50,
|
||||
VcomAndDataIntervalSetting = 0x50,
|
||||
/// This command indicates the input power condition. Host can read this flag to learn the battery condition.
|
||||
LOW_POWER_DETECTION = 0x51,
|
||||
LowPowerDetection = 0x51,
|
||||
/// This command defines non-overlap period of Gate and Source.
|
||||
TCON_SETTING = 0x60,
|
||||
TconSetting = 0x60,
|
||||
/// This command defines alternative resolution and this setting is of higher priority than the RES\[1:0\] in R00H (PSR).
|
||||
RESOLUTION_SETTING = 0x61,
|
||||
SOURCE_AND_GATE_SETTING = 0x62,
|
||||
ResolutionSetting = 0x61,
|
||||
SourceAndGateSetting = 0x62,
|
||||
/// This command reads the IC status.
|
||||
///
|
||||
/// Doesn't work! Waveshare doesn't connect the read pin
|
||||
GET_STATUS = 0x71,
|
||||
GetStatus = 0x71,
|
||||
/// Automatically measure VCOM. This command reads the IC status
|
||||
AUTO_MEASUREMENT_VCOM = 0x80,
|
||||
AutoMeasurementVcom = 0x80,
|
||||
/// This command gets the VCOM value
|
||||
///
|
||||
/// Doesn't work! Waveshare doesn't connect the read pin
|
||||
READ_VCOM_VALUE = 0x81,
|
||||
ReadVcomValue = 0x81,
|
||||
/// This command sets VCOM_DC value.
|
||||
VCM_DC_SETTING = 0x82,
|
||||
VcmDcSetting = 0x82,
|
||||
/// After this command is issued, the chip would enter the program mode.
|
||||
///
|
||||
/// After the programming procedure completed, a hardware reset is necessary for leaving program mode.
|
||||
///
|
||||
/// The only one parameter is a check code, the command would be excuted if check code = 0xA5.
|
||||
PROGRAM_MODE = 0xA0,
|
||||
ProgramMode = 0xA0,
|
||||
/// After this command is issued, the chip would enter the program mode.
|
||||
ACTIVE_PROGRAMMING = 0xA1,
|
||||
ActiveProgramming = 0xA1,
|
||||
/// The command is used for reading the content of OTP for checking the data of programming.
|
||||
///
|
||||
/// The value of (n) is depending on the amount of programmed data, tha max address = 0xFFF.
|
||||
READ_OTP = 0xA2,
|
||||
ReadOtp = 0xA2,
|
||||
/// Not shown in commands table, but used in init sequence
|
||||
POWER_OPTIMIZATION = 0xf8,
|
||||
PowerOptimization = 0xf8,
|
||||
}
|
||||
|
||||
impl traits::Command for Command {
|
||||
@@ -132,7 +131,7 @@ mod tests {
|
||||
|
||||
#[test]
|
||||
fn command_addr() {
|
||||
assert_eq!(Command::PANEL_SETTING.address(), 0x00);
|
||||
assert_eq!(Command::DISPLAY_REFRESH.address(), 0x12);
|
||||
assert_eq!(Command::PanelSetting.address(), 0x00);
|
||||
assert_eq!(Command::DisplayRefresh.address(), 0x12);
|
||||
}
|
||||
}
|
||||
|
||||
Reference in New Issue
Block a user